{"id":1005,"date":"2015-03-11T23:55:55","date_gmt":"2015-03-11T23:55:55","guid":{"rendered":"http:\/\/fivecedars.com\/?page_id=1005"},"modified":"2015-04-05T03:27:01","modified_gmt":"2015-04-05T03:27:01","slug":"fix-cracked-pot","status":"publish","type":"page","link":"https:\/\/fivecedars.com\/fix-cracked-pot\/","title":{"rendered":"Fix Cracked or Broken Flower Pot"},"content":{"rendered":"
Sooner or later you may need to Fix Cracked or Broken Flower Pot.
\nOver time it is possible to collect quite a few pots and some of them may be treasured and valuable.
\nAccidents will happen and its inevitable that a nice pot will be cracked or broken.
\nBut don\u2019t despair. It\u2019s not too much trouble to mend a broken pot given the right tools and materials and procedure.
\nFor our purposes we will be working on a pot with a rather large crack that goes in several directions but the methods here should work for almost any pot.
\nMost of the tools needed are found around the house but you may need to borrow a neighbors electric drill if you do not have one.
\n <\/div><\/div>\n
\u2022 Electric drill to drill holes in pot.
\n\u2022 Masonry bit a bit larger than the wire.
\n\u2022 Hand pump squirt bottle filled with water.
\n\u2022 Vise grip type pliers.
\n\u2022 Cutting pliers to cut wire.
\n\u2022 Chalk to mark the end of the crack.
\nMaterials:
\n\u2022 Wire to wrap pot
\n <\/div><\/div>\n<\/div>\n
If you are fixing a 12 inch pot you could do it on the kitchen table, but you would probably want to do a large pot out of doors.
\nA lawn is a perfectly suitable place to repair larger containers because the pot can be safely tipped on its side for ease of drilling.
\n <\/div><\/div>\n
\u2022 Find ends of crack or cracks and drill relief holes.
\n \u2022 Drill a hole on each side of the crack.
\n \u2022 Run wire around the pot crossing over to the hole on the opposite side and push 4 to 6 inches of wire through holes.
\n \u2022 Carefully twist the wires inside the pot.
\n \u2022 Trim wires, and pat self on back for saving money by repairing an expensive pot.
\n <\/div><\/div>\n<\/div>\n
Examine the crack and determine where it starts and where it ends.
\nA large crack is easy to find but you may need to look very closely to see where the crack ends.
\nOne way to find the end of the crack is to spray some water on the crack and then wipe it away with your hand. Look for hair line cracks.
\nOnce you find the end of the crack mark it with chalk.<\/p>\n
Drill small relief holes to stop the crack. This a an old trick used by windshield repair men. If a hole is drilled at the end of the crack it often can stop the crack from running further.
\nIt is important to place the hole at the very end of the crack so look carefully.
\nA 1\/4 inch hole should do the trick.
\n <\/div><\/div>\n
Now drill holes for the wire.
\nTry to determine where you will wrap the wire.
\nIn this case there was a bit of a rim so we decided to use this feature to help hold the wire in place.
\nDrill holes on both sides of the crack using a carbide drill that is just a little bit bigger than the wire. Larger holes make it easy to put the wire thought and allows a little leeway when we tighten the whole thing up.<\/p>\n
For this pot we drilled holes about 1-1\/2 inches from the crack and we wired it in one spot only.
\nYou may want to drill several holes along length of the crack.
\n <\/div><\/div>\n<\/div>\n
wire the pot together .
\nCopper wire seems to work well because its soft and easy to work with.
\nAny good hardware store will have a selection of copper wire.
\nLook for un-insulated ground wire.
\nIt\u2019s a little expensive so from now on when you go to the store and see they are selling a 5 foot cut off piece of copper wire for a buck, buy it and keep it for jobs like this.
\nTry to use some common sense as to the wire size.
\nYou want it to be big enough to do the job but not so big that it is hard to work with.
\nBe careful when threading the wire thought the holes.
\nToo much pressure could cause the pot to break.
\nMake sure you have enough wire on the inside of the pot to twist together. We allowed about 6 inches.
\n <\/div><\/div>\n
, but you probably will want to be careful with this one from now on.
\nObviously letting the crack fill with water and freezing or leaving the pot out all winter with soil inside is a no no with any pot.
\nAs a option you might want to put a bit of block bond or some type of cement patch on the inside to help stabilize the cracked sections.
\n <\/div><\/div>\n
\nIf you can see the price tag you will notice
\nthat this really nice terra cotta pot was
\nmarked down from $69.97 to TEN CENTS!
\n <\/div><\/div>\n